#Antenas yagi 10m install
#Antenas yagi 10m manual
#Antenas yagi 10m series

The mounting hardware uses sea-water resistant stainless steel and the aluminum is type T6 6066/6082, which is also used in aviation. The insulators are UV-resistant and designed for a wide temperature range. In most cases, no tuner is necessary the SWR minimum can be precisely set by adjusting the element lengths.ĭue to the robust construction and the absence of moving or electrically active components such as coils, traps, hairpins, etc., an InnovAntennas DXR beam is maintenance-free for many years. The result is the best possible matching over a wider band range than other antenna designs.

#Antenas yagi 10m manual

This negative effect was avoided by careful manual optimization. This is because each additional element on one band can cause interference on one band. With these multi-band Yagis, care has been taken to ensure that there are never more than the elements of 3 bands nested within each other. This construction also helps to avoid constant vibration even in light winds. (35mm) diameter in the middle and taper relatively quickly to achieve a good compromise between weight and strength. The DXR Yagis do not require any bracing of the boom. On the other hand, it is slightly heavier than a round boom of the same stiffness. A square boom has the advantage that the elements cannot twist in the plane.

#Antenas yagi 10m series

The DXR Series beams use a 1.97 x 1.97 in.

Very robust construction with still manageable package size.

Careful selection of materials without regard to cost.

Important features of InnovAntennas DXR Series Multi-Band HF Beams: For the XR Series Multi-band Yagis, equal attention was paid to a very solid construction and sufficiently small component and packaging size, to keep shipping costs within reasonable limits.

The XR Series interlaced-element antennas were optimized by G0KSC over a long period of time to achieve the best possible balance between compact size and performance. InnovAntennas XR Series Multi-Band HF Beams have short booms with full-size elements or capacity-loaded shortened-elements, all with excellent performance, making them very popular internationally. The DXR3 is a great beam for all casual and DX operators who want to use the three traditional HF bands. This is possible with a proven mechanical construction using top-grade materials including aircraft aluminum boom and elements, UV-resistant insulators and stainless steel hardware.

#Antenas yagi 10m install

(5.9m), the DXR3 is an HF tri-band beam that is easy to install and turn in a limited space.īuilt to handle high winds up to 107 mph (172 kph), this antenna is also suitable for very demanding locations, such as along a coastline. With a maximum element length of 38.0 ft. If you want to be assured of the absolute best performance and antenna stability, along with design consideration for your intended use, InnovAntennas are your only option.DXR3 produced are the MKII version, a 20, 15 and 10 meter HF Yagi with 6 interlaced elements on a short 10.2 ft. In many cases, never-achieved-before attributes such as Sky Temperature and G/T Figures are better with InnovAntennas Yagis (per metre of boom)*.

This is assuming the antenna needs to receive as well as it does transmit. However, on most VHF and all UHF bands, optimising in such a way is detrimental to the receive performance of the antenna and therefore inappropriate for the antenna to be designed this way. For example, on many HF bands, optimising an antenna for maximum gain is the way to go in most cases (but not all) provided a near 50 Ohm impedance can be maintained through its bandwidth. Our antennas are not designed to provide the best 'on-paper' gain figures, instead we design our antennas for the requirements of the band in question and for the specific purpose the antenna will be used. At InnovAntennaswe appreciate this fact and aim to deliver the product you want rather than the product that is most profitable for us. Considerations for light-weight, high wind handling ability, portability and long-term durability mean that no-one mechanical design can deliver a best-of-breed for all scenarios. A number of variants of each model can be produced in order to cater for the real-world requirements of both the commercial and ham customer.

InnovAntennas use the very latest in electromagnetic computer design technology in conjunction with Particle Swarm Optimisation methods (considered to be the best in optimisation technology today) to produce some of the most innovative and high performance antenna solutions available today.Įxclusive designs from some of the world's top antenna designers have been turned into professionally built, mechanically excellent antennas with a focus upon being manufactured the right way not the most cost effective way. Manufacturers of Innovative Yagi Antennas - home of the LFA Yagi by G0KSC